Thực hành trên phần mềm CIMCO

Phay CNC Leave a comment 519 Lượt xem

1 Giao diện chính của phần mềm CIMCO

Chú ý:
– Chế độ Tiện trong Cimco
Tại Ribbon File Type →chọn ISO Turning.
– Chế độ Phay trong Cimco
Tại Ribbon File Type → chọn ISO Milling.
2 Viết chương trình
Tab Editor → New → giao diện viết chương trình.

2.3 Mô phỏng chạy dao
Tab Backplot → nhấn Backplot Windown → nhấn Play (góc dưới bên phải)

Chú ý:
– Chế độ Tiện trong Cimco
Tại Ribbon File Type → chọn ISO Turning.
– Chế độ Phay trong Cimco
Tại Ribbon File Type → chọn ISO Milling.

4 Mô phỏng có phôi
Tab Backplot → nhấn Solid Animation → nhấn Play → mô phỏng gia công có phôi.
5 Lưu chương trình
Tab Editor → Save As → Chọn đường dẫn đến lưu → Đặt tên (Oxxxx) → nhấn Save

Bảng thông số chạy dao phay

BALL ENDMILL/ LOW-SP/ CU
Mill Length of cut Length of clear Spin

(vg/ Ph)

 Feed/Dwn F
(mm/ phút)		 Down(rgh)

(mm)

 Down(fin)

(mm)

 Side(rơh)
(Rước ăn
dao ngang)		 Side(fin)
(Rước ăn
dao ngang)		 Offset Available R
R6 50 4000 1000/23 1 0.8 2 0.4 0.09 R7.5 ~
51 ~ 70 3000 600/30 0.8 0.7 0.4 0.09
R5 40 4000 .1000/23 0.9 0.8 1.5 0.4 0.08 R6 ~
41 ~ 60 3500 600/30 0.7 0.6 0.4 0.08
R4 35 4000 900/30 0.7 0.6 1.2 0.3 0.08 R5 ~
36 ~ 50 400/40 0.5 0.45 0.3 0.08
R3 10 4000 900/30 0.6 0.45 0.9 0.25 0.08 R4
11 ~ 25 600/35 0.5 0.45 0.25
26 ~ 40 400/40 0.35 0.35 0.25 0.08
41 ~ 50 200/50 0.25 0.25 0.25 0.08
R2.5 ~ 8 4000 800/30 0.5 0.45 0.8 0.25 0.07 R3.5 ~
~ 15

~ 20

 600/30 0.4 0.35 0.25
400/35 0.3 0.25 0.25
R2 ~ 10 4000 700/30 0.4 0.3 0.7 0.12 0.07 R3 ~
11 ~ 20 500/30 0.35 0.3 0.12
21 ~ 30 400/35 0.3 0.25 0.15 0.07
31 ~ 40 200/60 0.15 0.15 0.15 0.07
41 ~ 50 200/50 0.1 0.15 0.15 0.07
R1.5 ~ 5 4000 600/35 0.35 0.3 0.6 0.1 0.05 R2.5 ~
6 ~ 15 400/40 0.25 0.2 0.1
16 ~ 25 300/50 0.2 0.15 0.07 0.06
26 ~ 35 200/70 0.15 0.1 0.07 0.06
36 ~ 40 200/60 0.1 0.07 0.07 0.06
R1 ~ 6 4000 400/40 0.2 0.1 0.48 0.1 0.05 R2 ~
7 ~ 15 300/50 0.15 0.1 0.1 0.05
16 ~ 25 200/55 0.15 0.1 0.07 0.06
26 ~ 35 150/70 0.1 0.07 0.07 0.06
R0.75 ~ 4 4000 400/40 0.2 0.1 0.42 0.07 0.04 R1 ~
5 ~ 8 300/50 0.15 0.1 0.07 0.05
9 ~ 12 200/70 0.15 0.1 0.06 0.06
13 ~ 16 200/70 0.1 0.06 0.06 0.06
17 ~ 20 200/70 0.07 0.05 0.05 0.06
~ 22 150/70 0.05 0.03 0.05
~ 30 150/70 0.03 0.02 0.05
R0.5 ~ 4 4000 400/45 0.15 0.08 0.34 0.06 0.03 R0.5 ~
~ 6 400/40 0.1 0.08 0.06
~ 8 300/50 0.1 0.07 0.05
~ 10 300/50 0.07 0.05 0.05
~ 12 200/60 0.07 0.05 0.04 0.03
~ 14 200/60 0.06 0.04 0.04
~ 16 150/70 0.04 0.03 0.04 0.04
~ 18 15070 0.03 0.02 0.03
~ 20 100/90 0.03 0.02 0.03 0..04
~ 22 100/80 0.02 0.01 0.03
R0.4 ~ 4 4000 300/45 0.1 0.08 0.3 0.05 0.02
5 ~ 8 200/60 0.08 0.05 0.04
9 ~ 12 100/70 0.06 0.04 0.03 0.02
R0.3 ~ 2 4000 200/70 0.07 0.05 0.25 0.04 0.02
~ 3 200/70 0.06 0.04 0.04
~ 4 150/80 0.06 0.03 0.03
~ 6 150/70 0.04 0.02 0.03 0.02
~ 8 100/90 0.03 0.02 0.02
~ 10 100/80 0.02 0.01 0.01
R0.25 ~ 2 4000 150/70 0.05 0.03 0.2 0.03 0.02
3 ~ 6 100/80 0.03 0.02 0.02 0.02
7 ~ 10 100/70 0.02 0.01 0.15 0.02 0.02
R0.2 ~ 2 4000 100/70 0.03 0.02 0.1 0.02 0.01
3 ~ 6 80/90 0.02 0.01 0.01
R0.15 ~ 1 4000 100/70 0.02 0.01 0.05 0.01 0.01
~ 2 80/80 0.02 0.01 0.01
~ 3 80/70 0.01 0.005 0.04 0.01

 

BALL ENDMILL / LOW-SP/ ST
Mill Length of cut Length of clear Spin

(vg/ Ph)

 Feed/Dwn F
(mm/ phút)		 Down(rgh)
(mm)		 Down(fin)

(mm)

 Side(rgh)
(Bước ăn
dao
llgílllg)		 Side(fin)
(Bước ăn
dao
Iigang)		 Offset Available R
R8 ~ 30 1600 330/15 0.8 0.6 2 0.4 0.07 R9.5 ~
31 ~ 60 1400 280/17 0.6 0.3 0.4 0.07
61 ~ 100 1200 230/20 0.3 0.2 0.3 0.07
R6 ~ 50 2200 370/13 0.6 0.4 1.5 0.35 0.07 R7.5 ~
51 ~ 70 1800 300/16 0.4 0.2 0.35 0.07
R5 ~ 40 2600 390/13 0.6 0.4 1 0.3 0.07 R6
41 ~ 65 2300 330/15 0.4 0.2 0.2. 0.07
R4 ~ 35 3000 420/12 0.5 0.35 0.7 0.3 0.07 R5 ~
36 ~ 60 2600 360/14 0.4 0.15 0.25 0.07
R3 ~ 10 4000 470/11 0.35 0.3 0.5 0.2 0.05 R4 ~
11 ~ 25 460/11 0.25 0.2 0.2 0.05
26 ~ 40 420/12 0.15 0.15 0.15 0.05
41 ~ 50 3000 220/23 0.07 0.07 0.1 0.05
R2.5 ~ 8 4000 400/12 0.3 0.3 0.4 0.2 0.05 R3.5 ~
~ 15 350/13 0.2 0.2 0.2
~ 20 300/15 0.15 0.2 0.2
R2 10 4000 330/15 0.2 0.2 0.4 0.1 0.05 R3 ~
11 ~ 20 320/15 0.1 0.1 0.1
21 ~ 30 200/24 0.1 0.1 0.1 0.05
31 ~ 40 160/28 0.05 0.05 0.05 0.03
R1.5 ~ 5 4000 280/17 0.2 0.2 0.3 0.1 0.05 R2.5 ~
6 ~ 15 260/18 0.1 0.1 0.1
16 ~ 25 200/25 0.03 0.03 0.05 0.05
26 ~ 35 130/35 0.02 0.2 0.05
36 ~ 40 100/45 0.02 0.02 0.03 0.03
R1 ~ 6 4000 160/28 0.15 0.15 0.25 0.1 0.05 R2 ~
7 ~ 15 150/30 0.1 0.1 0.08
16 ~ 25 110/42 0.05 0.05 0.05 0.03
26 ~ 35 90/50 0.01 0.01 0.05
R0.75 ~ 4 4000 150/28 0.1 0.1 0.2 0.07 0.03 R1 ~
5 ~ 8 130/30 0.07 0.07 0.06
9 ~ 12 110/42 0.05 0.05 0.05
13 ~ 16 100/42 0.03 0.03 0.05
17 ~ 20 100/45 0.02 0.02 0.03 0.01
~ 22 90/45 0.01 0.01 0.03
~ 30 80/55 0.01 0.01 0.03
R0.5 ~ 4 4000 130/35 0.05 0.05 0.15 0.05 0.01 R0.5 ~
~ 6 120/35 0.04 0.05 0.05
~ 8 115/40 0.04 0.05 0.05
~ 10 110/40 0.03 0.03 0.04
~ 12 100/45 0.03 0.03 0.04 0.005
~ 14 100/45 0.02 0.02 0.03
~ 16 90/45 0.015 0.02 0.03
~ 18 80/55 0.01 0.01 0.02
~ 20 70/63 0.01 0.01 0.02
~ 22 60/70 0.005 0.005 0.01
R0.4 ~ 4 4000 100/45 0.04 0.04 0.13 0.04 0.01
5 ~ 8 80/55 0.03 0.03 0.03
9 ~ 12 70/63 0.02 0.03 0.02
R0.3 ~ 2 4000 90/50 0.02 0.02 0.1 0.02 0.01
~ 3 80/55 0.02 0.02 0.02
~ 4 80/55 0.01 0.01 0.02
~ 6 70/63 0.01 0.01 0.01
~ 8 55/75 0.007 0.007 0.01
~ 10 50/80 0.005 0.005 0.01
R0.25 ~ 2 4000 60/70 0.01 0.01 0.07 0.02 0.01
3 ~ 6 60/70 0.007 0.01 0.02
7 ~ 10 50/80 0.005 0.005 0.01
R0.2 ~ 2 4000 60/70 0.01 0.01 0.05 0.01 0.01
3 ~ 6 60/70 0.005 0.005 0.01
R0.15 ~ 1 4000 60/70 0.007 0.007 0.03 0.005 0.005
~ 2 50/80 0.007 0.007 0.005
~ 3 50/70 0.005 0.005 0.005

 

FLAT ENDMILL / LOW-SP/CU
Mill Length of cut Length of clear Spin

(vg/ Ph)

 Feed/Dwn F

(mm/ phút)

 Down(rgh)
(mm)		 Down(fin)

(mm)

 Side
(Bước ăn dao
ngang)		 Offset Available R
016 ~ 40 1400 640/16 1.3 8 0.2 R9.5 ~
41~ 70 1100 390/20 0.8 0.1
012 ~ 40 3000 800/25 0.8 1 6 0.06 R7.5 ~
41~ 70 500/20 0.6 0.7 0.07
010 ~ 35 4000 800/25 0.7 0.9 5 0.05 R6 ~
36 ~ 60 2500 600/20 0.5 0.7 0.05
61~ 80 1200 400/20 0.3 0.4 0.06
08 ~ 32 4000 800/25 0.6 0.8 4 0.05 R5 ~
33 ~ 60 400/25 0.5 0.7 0.05
61 ~ 90 2000 200/45 0.4 0.5 0.06
06 ~ 25 4000 800/22 0.5 0.7 3 0.04 R4 ~
26 ~ 40 400/25 0.35 0.45 0.04
41 ~ 60 2000 200/40 0.2 0.3 0.05
05 ~13 4000 700/30 0.45 0.65 2.5 0.04 R3.5 ~
14 ~ 16 500/27 0.35 0.5
17 ~ 25 400/30 0.3 0.5
26 ~ 35 250/40 0.2 0.4 0.04
04 ~ 10 4000 600/32 0.4 0.6 2 0.03 R3 ~
11~ 20 400/33 0.3 0.4
21 ~ 35 270/35 0.25 0.4 0.03
36 ~ 50 2300 200/40 0.1 0.2 0.04
03 ~ 8 4000 550/30 0.35 0.55 1.5 0.03 R2.5 ~
9 ~ 15 400/30 0.25 0.4
16 ~ 25 300/40 0.2 0.35 0.03
26 ~ 35 200/50 0.1 0.25 0.03
36 ~ 40 2500 200/40 0.05 0.15 0.03
02 ~ 8 4000 440/33 0.25 0.4 1 0.02 R2 ~
9-12 400/30 0.2 0.3
13 ~ 25 300/37 0.1 0.2
26 ~ 35 200/50 0.05 0.1 0.02
01.8 ~ 6 4000 400/30 0.2 0.3 0.9 0.02 R1 ~
7 ~ 10 350/32 0.15 0.2 0.01
11 ~ 12 270/40 0.1 0.2 0.01
01.5 ~ 6 4000 400/30 0.15 0.25 0.75 0.02 R1 ~
7 ~ 10 330/34 0.1 0.2
11 ~ 20 200/55 0.05 0.1
21 ~ 30 100/80 0.05 0.1 0.01
01.2 ~ 6 4000 350/33 0.1 0.2 0.6 0.02 R1 ~
7 ~ 12 270/41 0.07 0.15 0.01
01 ~ 4 4000 300/37 0.1 0.2 0.5 0.01 R0.5 ~
5 ~ 8 250/44 0.07 0.15 0.01
8 ~ 12 160/65 0.05 0.12 0.01
13~ 20 100/70 0.04 0.1 0.01
00.9 ~ 6 4000 250/44 0.1 0.2 0.4 0.01
7 ~ 10 200/50 0.06 0.15
00.8 ~ 4 4000 250/40 0.08 0.15 0.4 0.01
5 ~ 8 200/50 0.06 0.1
9 ~ 12 100/70 0.05 0.08 0.01
13 ~ 16 100/55 0.03 0.07 0.01
00.7 ~ 4 4000 200/50 0.07 0.1 0.3 0.01
5 ~ 8 150/60 0.05 0.08
~ 10 100/65 0.03 0.06
0.06 0.1
5 ~ 8
9 ~ 12 80/70 0.03 0.06
~ 4
5 ~ 8
9 ~ 10 80/65 0.02 0.05
0.04 0.08
~ 6
0.03 0.06
~ 4
~ 6 60/70 0.01 0.03
0.01 0.01
FLAT ENDMILL / LOW-SP/CU
Mill Length of cut Length of clear Spin

(vg/ Ph)

 Feed/Dwn F

(mm/ phút)

 Down(rgh)
(mm)		 Down(fin)

(mm)

 Side
(Bước ăn dao
ngang)		 Offset Available R
016 ~ 40 1400 640/16 1.3 8 0.2 R9.5 ~
41~ 70 1100 390/20 0.8 0.1
012 ~ 40 3000 800/25 0.8 1 6 0.06 R7.5 ~
41~ 70 500/20 0.6 0.7 0.07
010 ~ 35 4000 800/25 0.7 0.9 5 0.05 R6 ~
36 ~ 60 2500 600/20 0.5 0.7 0.05
61~ 80 1200 400/20 0.3 0.4 0.06
08 ~ 32 4000 800/25 0.6 0.8 4 0.05 R5 ~
33 ~ 60 400/25 0.5 0.7 0.05
61 ~ 90 2000 200/45 0.4 0.5 0.06
06 ~ 25 4000 800/22 0.5 0.7 3 0.04 R4 ~
26 ~ 40 400/25 0.35 0.45 0.04
41 ~ 60 2000 200/40 0.2 0.3 0.05
05 ~13 4000 700/30 0.45 0.65 2.5 0.04 R3.5 ~
14 ~ 16 500/27 0.35 0.5
17 ~ 25 400/30 0.3 0.5
26 ~ 35 250/40 0.2 0.4 0.04
04 ~ 10 4000 600/32 0.4 0.6 2 0.03 R3 ~
11~ 20 400/33 0.3 0.4
21 ~ 35 270/35 0.25 0.4 0.03
36 ~ 50 2300 200/40 0.1 0.2 0.04
03 ~ 8 4000 550/30 0.35 0.55 1.5 0.03 R2.5 ~
9 ~ 15 400/30 0.25 0.4
16 ~ 25 300/40 0.2 0.35 0.03
26 ~ 35 200/50 0.1 0.25 0.03
36 ~ 40 2500 200/40 0.05 0.15 0.03
02 ~ 8 4000 440/33 0.25 0.4 1 0.02 R2 ~
9-12 400/30 0.2 0.3
13 ~ 25 300/37 0.1 0.2
26 ~ 35 200/50 0.05 0.1 0.02
01.8 ~ 6 4000 400/30 0.2 0.3 0.9 0.02 R1 ~
7 ~ 10 350/32 0.15 0.2 0.01
11 ~ 12 270/40 0.1 0.2 0.01
01.5 ~ 6 4000 400/30 0.15 0.25 0.75 0.02 R1 ~
7 ~ 10 330/34 0.1 0.2
11 ~ 20 200/55 0.05 0.1
21 ~ 30 100/80 0.05 0.1 0.01
01.2 ~ 6 4000 350/33 0.1 0.2 0.6 0.02 R1 ~
7 ~ 12 270/41 0.07 0.15 0.01
01 ~ 4 4000 300/37 0.1 0.2 0.5 0.01 R0.5 ~
5 ~ 8 250/44 0.07 0.15 0.01
8 ~ 12 160/65 0.05 0.12 0.01
13~ 20 100/70 0.04 0.1 0.01
00.9 ~ 6 4000 250/44 0.1 0.2 0.4 0.01
7 ~ 10 200/50 0.06 0.15
00.8 ~ 4 4000 250/40 0.08 0.15 0.4 0.01
5 ~ 8 200/50 0.06 0.1
9 ~ 12 100/70 0.05 0.08 0.01
13 ~ 16 100/55 0.03 0.07 0.01
00.7 ~ 4 4000 200/50 0.07 0.1 0.3 0.01
5 ~ 8 150/60 0.05 0.08
~ 10 100/65 0.03 0.06
00.6 ~ 4 4000 150/55 0.06 0.1 0.3 0.01
5 ~ 8 110/50 0.05 0.08
9 ~ 12 80/70 0.03 0.06 0.01
00.5 ~ 4 4000 130/60 0.05 0.1 0.2 0.01
5 ~ 8 100/50 0.04 0.08
9 ~ 10 80/65 0.02 0.05
00.4 ~ 3 4000 100/60 0.04 0.08 0.2 0.01
~ 6 70/70 0.03 0.06
00.3 ~ 2 4000 100/60 0.03 0.06 0.1 0.01
~ 4 70/70 0.02 0.04
~ 6 60/70 0.01 0.03
00.2 ~ 2 4000 50/60 0.01 0.01 0.1 0.01
~ 4 40/70 0.01 0.01

 

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *

Powered by Vân Hành Máy
© Copyright 2026, All Rights Reserved